top of page

JessLynnBabblin'

172: My Woodburning Process

Writer's picture: Jessica NacovskyJessica Nacovsky

Howdy! I've been woodburning for the past year, fine tuning the process as I go. Folk often ask about it so I'm taking the opportunity to break it down.


First I draw the design. Often I do so on tracing paper over the piece of wood to ensure it fits. Then I transfer it with charcoal pencil, rubbing from the tracing paper onto the wood with a spare wine cork. The project outlined, I'll touch up lighter areas with the charcoal pencil. Erasers are ineffective on charcoal and wood so I use sandpaper to remove mistakes.


Initially I was working with the woodburning wands that could double as soldering irons that plug directly into the wall. These had no mechanism for altering the heat and I couldn't achieve dark black shading with them. Eventually I invested in a woodburning kit that includes a power source that can charge two wands at once, as well as the wands themselves, and their various tips. Setting the heat nearly to the maximum temperature, I line with a narrow tip.


The linework done, I saturate the wood with water and get to painting. First I do the highlights with white gouache paint. The paint is opaque and colors painted over it are bolder than those painted on nude wood. With the whites laid out, I go over top with watercolor paint. Less pigment over a wider wet area gives for a softer gradient and is preferred for blending. Too much pigment ends up looking like acrylic paint, or marker, which can look cool, but is rarely the desired effect (for me).


To lend clarity to what is now a blurryish design with a muted outline, I re-line the image in black paint, which can be acrylic, watercolor, or gouache. Whatever is available will do. I've even used marker when that worked. I am open to the possibility of colored outlines in the future. Usually, I spray glossy varnish overtop after lining the woodburning. See, for the watercolors to have that nice blend seep into the wood, I have to apply the paint before the first varnish. The outline, however, can actually benefit from my having varnished first. The glossy exterior is appropriate for marker lining, and the burn-divot can work to contain watery paints that otherwise would have been absorbed, if that makes sense. The burn lines are jagged inside, not level, and the varnish spray evens them out somewhat.


So, either before or after lining, I spray varnish. If before, I spray again after. Varnish is the finishing touch on the front. As for the back, I mark where the hook must be positioned for the piece to hang straight. Then I screw the hook in, adding a few washers so the screw doesn't go fully through the thin wood slice. Beneath the hook, I sign my name via woodburning with the hot wand. Though, my sister just got me a personalized brand with my married name so I think I'll start using that.


Normally, that's the end. However, when making glow-in-the-dark designs, I apply acrylic glow-paint over the desired areas in thin watery layers, allow those to dry, and varnish over them. If I paint thickly, the glow is more intense with less labor, but the paint dries lumpy. Can't have that! I've found that it takes about seven layers for a nice smooth glow. Again, the piece isn't done until varnished. A cool thing is that I can use paint markers over glow-paint in order to tint it the desired hue. While glow paint isn't opaque, it does carry some minimally pale green pigment which is rarely the desired color.


A headache I've been faced with is handling cracks in woodburnings. To avoid this, I've taken to soaking wood before use, in order to set cracked pieces aside. But, I only started doing this because I was having the issue. After much trial and error, I've found that the solution to cracked woodburnings is to seal the back of the crack with hot glue, and the front with acrylic paint that's been mixed with flour. Pure acrylic or gouache paint reduces too much upon drying so while it appears level with the wood prior, it's not. I use a business card or similar flat edged object to scrap excess paint from the crack. Sanding is an option for once the crack is full, but risks dirtying the area, so better if it's flat to start with. I haven't tried clay but I have tried non-hot craft glues and wasn't impressed by how they pooled out of the back, demanding more sanding. The earlier in the process the crack occurs, the easier to resolve. I noticed recently that the cracking seems to occur when I saturate a small area of the wood with water, as opposed to the entire thing. Going forward, I'm aiming for full saturation during the painting phase.


I hope you found any of this informative! I drop a blog post every Monday. Toodles!


Newsletter

Howdy! This Saturday, October 19th, I'll be selling art at The Art Walk at Hotel McCoy in College Station Texas. I've spent the past week assembly-lining woodburnings for that event. These include five Kodamas, two 5.5 inch jack o'lanterns, Jack from Animal Crossing, a mandrake, and a two headed galaxy cow. They are currently fully woodburned, colored, and lined. What's left is applying glow-paint and minor touch ups. They also need hooks on their backs and to be signed. Not sure what else I'm making this week.


I started writing the story I've been thinking about for the last couple of weeks, that's somewhere between speculative and sci-fi. I haven't made a ton of progress yet. I'm also still querying Soul Walker, my paranormal women's fiction novel.


I finished reading The Unbearable Lightness of Being by Milan Kundera, yesterday. It's an odd book, largely about a couple and a handful of their peers, wherein the narrator initially appears as a too-close friend, before late in the story, being revealed as the author, who, breaking the fourth wall, acknowledges that the characters are his creation. The pacing varies with the story initially told in chronological order before flipping forward, touching on what would have been the climax in another book, and jumping back. I wasn't invested in most of the characters and there are long spiels that amount to moral lectures. Still, the plot was interesting and the structure, while unfamiliar, was refreshing.


I'm now reading The Martian by Andy Weir. I'm about six chapters in and it's leaning heavy into math and science but it's definitely a page turner.


Thanks for stopping by! I drop a Newsletter every Monday. Toodles!

5 views0 comments

Recent Posts

See All

176: Free Leathercraft Resources

Howdy! Full disclosure: I just realized it's Monday at 8:49PM. I was focused on revising the outline for my NaNoWriMo novel today and...

Comments


bottom of page